For decades we have been installing clothes dryers with hose clamps over aluminum dryer hose. You take your dryer hose and hose clamps and climb behind the dryer or lean over the top of the dryer. You then take a screw driver and carefully place your hose over the dryer or wall duct while holding a screwdriver in one hand and positioning the hose with the other. You then slowly screw down the hose clamp, but not too tight... after what seems to be a very long time you hope your connection is snug enough to stay on while you move your dryer back into install position. When you slide your dryer back, you have to be careful not to push back too far, crushing the hose and losing the work you just did.
The BETTER Way
There is now a better way. Ziggurat Products new product line Snap to Vent is revolutionizing and making dryer vent installation easy and safe to use. The beauty of Snap to Vent is that you can pre-attach the dryer hose before you have to get back to the dryer in awkward positions. You can simply attach the hose to either the patented 90 Degree Elbow or the Straight Connector. Now take the hose and slide the snap connector fingers into the dryer hose. Take the dryer hose and snap connector and snap into the 90 Degree Elbow or Straight Connector.
LXLMS
You will love how easy and stress free the connection fits together. After the dryer hose is attached to the snap connectors it is now time to connect to the dryer and wall duct. Use the seal ring to make the 90 Degree Elbow or Straight connector nice and snug to the dryer duct, creating an air tight seal. Push the dryer back to the wall until the 90 Degree Elbow hits the back of the wall. The dryer hose is protected from crushing and is less likely to create air flow leakage. You can decide what will work best for your personal dryer setup at home. Depending on your dryer vent situation you may need 90 Degree Elbow and Straight, 2 90 Degree Elbows or 2 Snap to Vent Straights. Whatever your configuration we can help you install your dryer with ease.
No more crushed hoses restricting airflow. Use the Snap to Vent for quick and easy dryer installation, easy to clean out preventing dryer fires and continually good airflow to help dry your clothes quickly as well as save you money on your utility bills.
Choose Snap to Vent, the better choice!
You can purchase Snap to Vent on Amazon.com or at our website at www.snaptovent.com
The Old Way
For decades we have been installing clothes dryers with hose clamps over aluminum dryer hose. You take your dryer hose and hose clamps and climb behind the dryer or lean over the top of the dryer. You then take a screw driver and carefully place your hose over the dryer or wall duct while holding a screwdriver in one hand and positioning the hose with the other. You then slowly screw down the hose clamp, but not too tight... after what seems to be a very long time you hope your connection is snug enough to stay on while you move your dryer back into install position. When you slide your dryer back, you have to be careful not to push back too far, crushing the hose and losing the work you just did.
The BETTER Way
There is now a better way. Ziggurat Products new product line Snap to Vent is revolutionizing and making dryer vent installation easy and safe to use. The beauty of Snap to Vent is that you can pre-attach the dryer hose before you have to get back to the dryer in awkward positions. You can simply attach the hose to either the patented 90 Degree Elbow or the Straight Connector. Now take the hose and slide the snap connector fingers into the dryer hose. Take the dryer hose and snap connector and snap into the 90 Degree Elbow or Straight Connector.
LXLMS
You will love how easy and stress free the connection fits together. After the dryer hose is attached to the snap connectors it is now time to connect to the dryer and wall duct. Use the seal ring to make the 90 Degree Elbow or Straight connector nice and snug to the dryer duct, creating an air tight seal. Push the dryer back to the wall until the 90 Degree Elbow hits the back of the wall. The dryer hose is protected from crushing and is less likely to create air flow leakage. You can decide what will work best for your personal dryer setup at home. Depending on your dryer vent situation you may need 90 Degree Elbow and Straight, 2 90 Degree Elbows or 2 Snap to Vent Straights. Whatever your configuration we can help you install your dryer with ease.
No more crushed hoses restricting airflow. Use the Snap to Vent for quick and easy dryer installation, easy to clean out preventing dryer fires and continually good airflow to help dry your clothes quickly as well as save you money on your utility bills.
Choose Snap to Vent, the better choice!
You can purchase Snap to Vent on Amazon.com or at our website at www.snaptovent.com
